How To Use a Stump Grinder

There’s a way of triumphant accomplishment that comes from lowering dead or unwanted trees. (Not to say the joys of yelling, But that feeling fades pretty quickly once you look down and see unsightly—and very stubborn—Stump milling.

If you hire a landscaper or arborist to chop down the trees, they typically leave the stumps behind, unless you pay a further fee. Stump-removal prices vary widely across the country and are supported by the diameter of the stump, but it typically costs between $100 and $200 to get rid of a stump that’s 24 inches in diameter or smaller. And that’s a good price if you’ve only got one stump to get rid of . But, if you've got two or more stumps, you'll save a substantial amount of cash by renting a stump grinder.

A gas-powered stump grinder rents for about $100 per day, counting on the dimensions of the machine. And if you share the rental expense with one or two stump-plagued neighbors, renting is certainly the more economical thanks to going. you will need a vehicle with a trailer hitch to tow the machine, which weighs about 1,000 pounds. Or, for a nominal fee, most rental dealers will drop off and devour the grinder.

To remove the 30-in.-dia. scarlet maple stump, I rented a Vermeer Model SC252 stump grinder. it's a strong 25-hp engine and 16-in.-dia. cutting wheel that's studded with 16 forged-steel teeth. this is often a loud, powerful machine with a classy mechanism , but it's surprisingly simple to work . But, before you crank up the motor and begin grinding away, it’s important to prep the world for the stumpectomy.

Start by ensuring all kids and pets are indoors, or if they’re outdoors, keep them well faraway from the world and under constant adult supervision. Then, use a round-point shovel or garden mattock to get rid of any rocks from round the base of the stump [1]. this is often important because if the spinning cutting wheel hits a rock, it can shoot out sort of a missile and cause serious injury. Plus, rocks can dull or damage the teeth on the cutting wheel, which are expensive to exchange.

Next, check the peak of the stump. If it’s protruding out of the bottom quite 6 inches approximately, use a sequence saw to trim it as on the brink of the bottom as possible [2]. While this step isn’t absolutely necessary, it'll prevent quite little bit of time because removing 6 inches of the Stump grinding with a chainsaw is far quicker than using the grinder.

After donning the acceptable safety gear, start the grinder and drive it to within 3 feet of the stump. Use the hydraulic lever to boost the cutting wheel until it’s a couple of inches above the stump. Slowly drive the machine forward to position the wheel directly over the stump's front edge [3]. Engage the facility lever to start out the wheel spinning, then slowly lower it about 3 in. in to the stump grinding.

Next, use the hydraulic lever to slowly swing the wheel from side to side to filter out all the wood within the cutting range. Then, raise the wheel, advance the machine forward a couple of inches, and repeat the method. While operating the machine, always stand at the instrument panel, which is found near the rear of the machine and well faraway from the cutting wheel.

Little by little, continue grinding and advancing your way through to the opposite side of the stump. Raise the cutting wheel, shift into reverse, and return to the starting spot. Repeat the grinding process until the surface of the Stump removal is a minimum of 4 in. below the extent of the encompassing ground. At now, you'll drive the grinder off to at least one side, far away from the excavated hole.

Now, discover all the wood chips and fill the crater with screened topsoil [4]. (The wood chips are often used as mulch in flowerbeds and around trees and shrubs.) Lightly rake the soil, opened up a good layer of grass seed, then rake the seeds into the soil [5]. Water the world and canopy the seeds with mulch hay.

Be sure to water the world a day for 2 weeks. Remove the hay once you see the grass seedlings poking through.